How to Adjust the Governor on a Yamaha Golf Cart

How to Adjust the Governor on a Yamaha Golf Cart

Your Yamaha golf cart’s governor is a critical component that controls the maximum speed of the cart. If the governor is not adjusted properly, your cart may not reach its full speed, or it may even run too fast and be unsafe.

Adjusting the governor on a Yamaha golf cart is a relatively simple task that can be completed in just a few minutes. However, it is important to follow the steps carefully in order to avoid damaging the cart.

In this article, we will walk you through the process of adjusting the governor on a Yamaha golf cart. We will provide step-by-step instructions and images to help you understand the process.

Before you begin, make sure you have the following tools:

• A Phillips head screwdriver
• A flathead screwdriver
• A torque wrench
• A set of metric sockets

Now, let’s get started!

Step	Action	Explanation
1	Locate the governor on your Yamaha golf cart.	The governor is a small, metal box located on the engine. It is usually near the carburetor.
2	Remove the governor cover.	The governor cover is a small, metal plate that covers the governor. It is usually held in place by two screws.
3	Adjust the governor screw.	The governor screw is a small, Phillips head screw located inside the governor. Turning the screw clockwise will increase the speed limit, and turning it counterclockwise will decrease the speed limit.
4	Reinstall the governor cover.	Once you have adjusted the governor screw, reinstall the governor cover.
5	Test the golf cart.	Take the golf cart for a test drive and make sure that the speed limit is correct.

How to Adjust the Governor on a Yamaha Golf Cart

Tools and Materials Needed

To adjust the governor on a Yamaha golf cart, you will need the following tools and materials:

• A Phillips head screwdriver
• A flathead screwdriver
• A 10mm wrench
• A 12mm wrench
• A 14mm wrench
• A torque wrench
• A feeler gauge

Locating the Governor

The governor is located on the engine of the golf cart. It is a small, cylindrical device with a black cap. The governor is connected to the throttle cable by a rod.

How to Adjust the Governor

1. Turn off the engine and allow it to cool down.
2. Locate the governor on the engine.
3. Remove the black cap from the governor.
4. Use a Phillips head screwdriver to loosen the two screws that hold the governor in place.
5. Use a flathead screwdriver to pry the governor up and out of the engine.
6. Use a 10mm wrench to loosen the locknut on the governor.
7. Use a 12mm wrench to turn the adjusting screw clockwise to increase the speed limit or counterclockwise to decrease the speed limit.
8. Retighten the locknut.
9. Reinstall the governor in the engine.
10. Replace the black cap.
11. Start the engine and test the speed limit.

Adjusting the governor on a Yamaha golf cart is a relatively simple task that can be completed in a few minutes. By following these steps, you can ensure that your golf cart is operating at its optimal speed.

3. Adjusting the Governor

To adjust the governor on a Yamaha golf cart, you will need the following tools:

• A Phillips head screwdriver
• A flathead screwdriver
• A torque wrench
• A 10mm socket wrench
• A 12mm socket wrench

1. Locate the governor. The governor is located on the engine, near the carburetor. It is a small, black box with a potentiometer knob on the front.
2. Turn off the engine and disconnect the battery. This will prevent you from accidentally starting the engine while you are working on the governor.
3. Remove the air cleaner cover. This will give you access to the governor.
4. Locate the governor adjustment screw. The governor adjustment screw is a small, Phillips head screw located on the side of the governor.
5. Turn the governor adjustment screw clockwise to increase the speed limit, or counterclockwise to decrease the speed limit. Turn the screw in small increments, and test the speed of the golf cart after each adjustment.
6. Reinstall the air cleaner cover.
7. Reconnect the battery.
8. Test the golf cart to make sure the governor is adjusted correctly. The golf cart should now be able to reach the desired speed limit.

4. Testing the Governor

To test the governor on a Yamaha golf cart, you will need to:

1. Start the engine and let it warm up for a few minutes.
2. Press the accelerator pedal all the way to the floor. The golf cart should reach the desired speed limit and then maintain that speed without surging or bogging down.
3. If the golf cart does not reach the desired speed limit, or if it surges or bogs down, you will need to adjust the governor again.

Once you have adjusted the governor and the golf cart is running smoothly, you can enjoy your ride.

How do I adjust the governor on a Yamaha golf cart?

1. Locate the governor. The governor is a small, metal device located on the engine. It is usually near the carburetor.
2. Turn the governor screw. The governor screw is a small, Phillips-head screw located on the side of the governor. Turn the screw clockwise to increase the speed limit, and counterclockwise to decrease the speed limit.
3. Test the speed limit. Once you have adjusted the governor, start the engine and let it warm up. Then, press the accelerator pedal to see how fast the cart goes. If the speed is not what you want, adjust the governor screw again and test the speed again.

What is the purpose of the governor on a golf cart?

The governor is a safety device that limits the speed of the golf cart. This prevents the cart from going too fast and causing an accident.

What happens if I remove the governor from my golf cart?

If you remove the governor from your golf cart, the cart will be able to go faster than it was designed to. This can be dangerous, as it increases the risk of an accident.

**How often should I adjust the governor on my golf cart?

You should only adjust the governor if you need to change the speed limit. If you do not need to change the speed limit, there is no need to adjust the governor.

What are some other ways to limit the speed of my golf cart?

In addition to the governor, there are a few other ways to limit the speed of your golf cart. These include:

• Using a speed limiter switch
• Installing a governor bypass kit
• Installing a lower gear ratio

**I am having trouble adjusting the governor on my golf cart. What should I do?

If you are having trouble adjusting the governor on your golf cart, you can take it to a qualified mechanic. They will be able to adjust the governor for you and make sure that it is working properly.

In this blog post, we have discussed how to adjust the governor on a Yamaha golf cart. We have covered the steps involved in the process, as well as some of the common mistakes that people make. We hope that this information has been helpful, and that you are now able to adjust the governor on your own.

Here are some key takeaways from this blog post:

• The governor is a device that limits the speed of a golf cart.
• The governor is located on the engine of the golf cart.
• To adjust the governor, you will need to remove the governor cover.
• The governor is adjusted by turning the governor screw.
• Turning the governor screw clockwise will increase the speed of the golf cart.
• Turning the governor screw counterclockwise will decrease the speed of the golf cart.

Be sure to follow the steps in this blog post carefully, and do not attempt to adjust the governor if you are not comfortable doing so. If you have any questions, please consult with a qualified mechanic.