How to Disable the Governor on a Golf Cart

AvatarByMatthew Woods How To Guides

How to Disable the Governor on a Golf Cart

Golf carts are a convenient way to get around a golf course, but they can be a bit slow. If you’re looking for a way to get a little more speed out of your golf cart, you may be wondering how to disable the governor.

The governor is a device that limits the speed of a golf cart. It does this by regulating the flow of fuel to the engine. By disabling the governor, you can increase the speed of your golf cart.

However, it’s important to note that disabling the governor can be dangerous. Golf carts are not designed to go at high speeds, and doing so can increase the risk of accidents.

If you decide to disable the governor on your golf cart, be sure to do so carefully and only when you’re in a safe environment.

In this article, we’ll discuss how to disable the governor on a golf cart. We’ll provide step-by-step instructions, as well as tips on how to do it safely.

We’ll also discuss the risks of disabling the governor and why it’s important to only do so when you’re in a safe environment.

Step Instructions Image
1 Locate the governor on your golf cart. It is usually a small, black box located under the hood.
2 Remove the governor from the golf cart. There will be a few screws holding it in place.
3 Replace the governor with a blanking plate. This will prevent the governor from being reinstalled.

What is a Governor on a Golf Cart?

A governor is a device that limits the speed of a golf cart. It is typically located on the engine and is either a mechanical or electronic device. Mechanical governors use a spring-loaded arm to physically limit the throttle, while electronic governors use a sensor to measure the engine speed and then send a signal to the throttle to reduce it.

Governors are used for a variety of reasons, including safety, emissions, and battery life. By limiting the speed of the golf cart, governors can help to prevent accidents, reduce emissions, and extend the life of the battery.

How Does a Governor Work?

Mechanical governors use a spring-loaded arm to physically limit the throttle. The arm is connected to the throttle linkage and as the engine speed increases, the spring pushes against the arm, limiting the amount of throttle that can be applied.

Electronic governors use a sensor to measure the engine speed and then send a signal to the throttle to reduce it. The sensor is typically located on the flywheel or crankshaft and sends a signal to the governor’s electronic control unit (ECU). The ECU then sends a signal to the throttle to reduce it.

How to Disable a Governor on a Golf Cart

Disabling a governor on a golf cart is not recommended and can be dangerous. If you do decide to disable the governor, it is important to do so carefully and to understand the risks involved.

To disable a mechanical governor, you will need to:

1. Remove the governor from the engine.
2. Disconnect the throttle linkage from the governor.
3. Reinstall the governor.

To disable an electronic governor, you will need to:

1. Locate the governor’s ECU.
2. Disconnect the ECU from the battery.
3. Reinstall the ECU.

It is important to note that disabling a governor will void your golf cart’s warranty and could make it illegal to operate on some courses.

Governors are an important safety feature on golf carts. They help to prevent accidents, reduce emissions, and extend the life of the battery. If you are considering disabling the governor on your golf cart, it is important to weigh the risks and benefits carefully.

Why would you want to disable the governor on a golf cart?

There are a few reasons why you might want to disable the governor on a golf cart.

  • To increase the top speed. The governor is a device that limits the maximum speed of a golf cart. By disabling the governor, you can increase the top speed of your golf cart. This can be useful if you need to get around quickly or if you want to have more fun on the golf course.
  • To improve acceleration. The governor can also affect the acceleration of a golf cart. By disabling the governor, you can make your golf cart accelerate more quickly. This can be useful if you need to get up to speed quickly or if you want to pass other golf carts on the course.
  • To improve fuel economy. Some people believe that disabling the governor can improve the fuel economy of a golf cart. This is because the governor can cause the engine to work harder than necessary, which can lead to decreased fuel economy. However, there is no scientific evidence to support this claim.

How to disable the governor on a golf cart?

Disabling the governor on a golf cart is a relatively simple process. However, it is important to note that disabling the governor can void your warranty and make your golf cart unsafe to operate. If you are not comfortable working on your golf cart, you should take it to a qualified mechanic to have the governor disabled.

To disable the governor on a golf cart, you will need to:

1. Locate the governor. The governor is typically located on the engine. It is a small, cylindrical device with a black cap.
2. Remove the governor cap. The governor cap is held in place by a small screw. Use a screwdriver to remove the screw and remove the cap.
3. Disconnect the governor wire. The governor wire is a small, black wire that connects the governor to the engine. Use a pair of pliers to disconnect the wire.
4. Replace the governor cap. Once the governor wire is disconnected, replace the governor cap and tighten the screw.

After you have disabled the governor, you should test your golf cart to make sure that it is operating properly. Be sure to drive the golf cart at a safe speed and avoid sharp turns.

Note: Disabling the governor on a golf cart can void your warranty and make your golf cart unsafe to operate. If you are not comfortable working on your golf cart, you should take it to a qualified mechanic to have the governor disabled.

How do I disable the governor on my golf cart?

There are a few different ways to disable the governor on a golf cart. The most common way is to remove the governor chip from the engine control unit (ECU). This can be done by following these steps:

1. Locate the ECU on your golf cart. It is typically located under the hood or in the passenger compartment.
2. Remove the ECU cover.
3. Locate the governor chip. It is a small, rectangular chip that is typically located on the circuit board of the ECU.
4. Remove the governor chip by carefully prying it up with a small screwdriver.
5. Replace the ECU cover.
6. Start the golf cart and test the governor. The governor should now be disabled.

Another way to disable the governor on a golf cart is to install a governor delete kit. A governor delete kit is a device that is installed between the ECU and the throttle body. It bypasses the governor and allows the engine to rev to its full potential.

To install a governor delete kit, follow these steps:

1. Locate the throttle body on your golf cart. It is typically located on the front of the engine.
2. Remove the throttle body cover.
3. Locate the governor linkage. It is a small rod that connects the throttle body to the governor.
4. Disconnect the governor linkage from the throttle body.
5. Install the governor delete kit between the ECU and the throttle body.
6. Reattach the throttle body cover.
7. Start the golf cart and test the governor. The governor should now be disabled.

It is important to note that disabling the governor on a golf cart can void your warranty. It can also make your golf cart more dangerous to operate. Only disable the governor if you are confident in your ability to do so safely.

What are the risks of disabling the governor on a golf cart?

There are a few risks associated with disabling the governor on a golf cart. These include:

  • Increased speed: A golf cart with a disabled governor can reach speeds that are unsafe for operation on a golf course.
  • Reduced braking ability: A golf cart with a disabled governor will have reduced braking ability, which can make it more difficult to stop in an emergency.
  • Increased risk of accidents: A golf cart with a disabled governor is more likely to be involved in an accident.

It is important to weigh the risks and benefits of disabling the governor on a golf cart before making a decision. If you decide to disable the governor, be sure to do so carefully and only if you are confident in your ability to operate the golf cart safely.

Is it legal to disable the governor on a golf cart?

The legality of disabling the governor on a golf cart varies from state to state. In some states, it is illegal to disable the governor on any motor vehicle. In other states, it is only illegal to disable the governor on a golf cart that is being used on a public road.

It is important to check the laws in your state before disabling the governor on your golf cart. If you are caught driving a golf cart with a disabled governor, you could be fined or even have your license revoked.

How can I enable the governor on my golf cart if I change my mind?

If you decide to enable the governor on your golf cart, you can do so by following these steps:

1. Locate the governor chip on the ECU.
2. Reattach the governor chip to the ECU.
3. Replace the ECU cover.
4. Start the golf cart and test the governor. The governor should now be enabled.

It is important to note that enabling the governor on a golf cart can make it less powerful and less responsive. If you are not satisfied with the performance of your golf cart with the governor enabled, you may want to consider disabling the governor again.

disabling the governor on a golf cart is a relatively simple process that can be completed in a few minutes. However, it is important to note that doing so can void your warranty and make your golf cart unsafe to operate. If you are not comfortable working on your own golf cart, it is best to have a qualified technician perform the modification.

Here are the key takeaways from this article:

  • The governor is a device that limits the speed of a golf cart.
  • Disabling the governor can increase the top speed of your golf cart.
  • Disabling the governor can void your warranty and make your golf cart unsafe to operate.
  • If you are not comfortable working on your own golf cart, it is best to have a qualified technician perform the modification.

Author Profile

Matthew Woods
Matthew Woods
Hello, fellow golf enthusiasts! I’m Matthew Woods, the founder of GolfPGAChampionship.com.

My journey with golf is a story of passion, perseverance, and a little twist of fate. Growing up in the picturesque town of Charleston, South Carolina, I found myself captivated by golf, a fascination that was partly kindled by sharing a last name with the legendary Tiger Woods.

This platform is more than just a website; it’s a culmination of my life’s experiences in golf. Here, I share in-depth analyses of PGA championships, personal anecdotes from my golfing journey, and tips for golfers at all levels. My aim? To make golf accessible and enjoyable for everyone, from eager beginners to seasoned players.

GolfPGAChampionship.com is a testament to my belief that golf is not just a sport, but a journey filled with learning, challenges, and personal growth. I invite you to join me in this journey, to explore the beautiful game of golf through my eyes and experiences.

Welcome to GolfPGAChampionship.com – let’s make every swing count!