How to Check a Solenoid on a Golf Cart

How to Check a Solenoid on a Golf Cart

If your golf cart is not starting, or if it is starting but not running smoothly, it could be a problem with the solenoid. The solenoid is a small, but important, part of the golf cart’s engine that controls the flow of electricity to the starter motor. If the solenoid is not working properly, it can prevent the starter motor from engaging, which will prevent the engine from starting.

Checking the solenoid is a relatively simple task that can be done at home with a few basic tools. In this article, we will walk you through the steps of checking the solenoid on a golf cart. We will also provide some tips on how to troubleshoot other potential problems with your golf cart’s starting system.

What is a Solenoid?

A solenoid is an electromechanical device that converts electrical energy into mechanical energy. In the case of a golf cart, the solenoid uses electricity to create a magnetic field that pulls the starter plunger into the starter housing. This action engages the starter motor, which starts the engine.

The solenoid is a relatively simple device, but it is an essential part of the golf cart’s starting system. If the solenoid is not working properly, it can prevent the engine from starting.

How to Check a Solenoid on a Golf Cart

Checking the solenoid on a golf cart is a relatively simple task that can be done at home with a few basic tools. Here are the steps involved:

1. Locate the solenoid. The solenoid is usually located on the starter motor. It is a small, cylindrical-shaped device with two terminals.
2. Disconnect the battery. Before you can check the solenoid, you need to disconnect the battery. This will prevent you from accidentally getting shocked.
3. Test the solenoid. To test the solenoid, you will need a multimeter. Set the multimeter to the ohms setting.
4. Connect the multimeter to the solenoid terminals. One terminal should be labeled “S” and the other terminal should be labeled “M”.
5. Turn the key to the “On” position. This will energize the solenoid.
6. Check the multimeter reading. The multimeter should read “0” ohms. If the multimeter reads anything other than “0” ohms, the solenoid is bad and needs to be replaced.

Troubleshooting Other Starting Problems

If the solenoid is not the problem, there are a few other things you can check to troubleshoot the starting problem. Here are a few tips:

• Check the battery. Make sure the battery is properly charged and that the terminals are clean and tight.
• Check the starter motor. The starter motor could be bad if it is not engaging properly.
• Check the wiring. The wiring between the battery, the solenoid, and the starter motor could be damaged or loose.

If you have checked all of these things and the golf cart is still not starting, it is time to take it to a qualified mechanic.

How To Check Solenoid On Golf Cart?

| Step | Action | Result |
|—|—|—|
| 1. Locate the solenoid. | The solenoid is typically located near the starter motor. |
| 2. Remove the solenoid’s electrical connector. | This will disconnect the solenoid from the electrical system. |
| 3. Use a multimeter to check the solenoid’s resistance. | The resistance should be between 50 and 100 ohms. |
| 4. If the resistance is not within spec, replace the solenoid. | |

The solenoid is a vital part of your golf cart’s starting system. It is responsible for sending a signal to the starter motor, which starts the engine. If the solenoid is not working properly, your golf cart will not start.

This guide will show you how to check the solenoid on your golf cart. We will cover the following topics:

• Identifying the solenoid
• Testing the solenoid
• Replacing the solenoid

Identifying the Solenoid

The solenoid is a cylindrical device that is located on the starter motor. It is typically about 2 inches in diameter and 3 inches long. It is usually made of metal and has a black or brown casing.

The solenoid has two terminals: a battery terminal and a starter motor terminal. The battery terminal is connected to the positive battery terminal, and the starter motor terminal is connected to the starter motor.

The solenoid also has a plunger. The plunger is a metal rod that is connected to the starter motor. When the starter button is pressed, the plunger is activated and sends a signal to the starter motor.

Testing the Solenoid

There are a few ways to test the solenoid. One way is to use a multimeter to check for continuity. Another way is to use a test light to check for power.

To test the solenoid with a multimeter, follow these steps:

1. Turn off the golf cart’s engine.
2. Disconnect the battery cables from the battery.
3. Set the multimeter to the continuity setting.
4. Touch the positive multimeter probe to the battery terminal on the solenoid.
5. Touch the negative multimeter probe to the starter motor terminal on the solenoid.

If the multimeter shows continuity, the solenoid is working properly. If the multimeter does not show continuity, the solenoid is faulty and needs to be replaced.

To test the solenoid with a test light, follow these steps:

1. Turn off the golf cart’s engine.
2. Disconnect the battery cables from the battery.
3. Connect the test light to the battery terminals.
4. Touch the test light probe to the battery terminal on the solenoid.

If the test light comes on, the solenoid is working properly. If the test light does not come on, the solenoid is faulty and needs to be replaced.

Replacing the Solenoid

Replacing the solenoid is a relatively simple task. However, it is important to follow the instructions carefully to avoid damaging the golf cart.

To replace the solenoid, follow these steps:

1. Turn off the golf cart’s engine.
2. Disconnect the battery cables from the battery.
3. Remove the starter motor cover.
4. Disconnect the solenoid wires from the starter motor.
5. Remove the solenoid bolts.
6. Remove the solenoid.
7. Install the new solenoid.
8. Connect the solenoid wires to the starter motor.
9. Replace the starter motor cover.
10. Reconnect the battery cables to the battery.

The solenoid is a vital part of your golf cart’s starting system. If the solenoid is not working properly, your golf cart will not start. This guide has shown you how to check the solenoid and replace it if necessary.

By following these steps, you can keep your golf cart running smoothly and safely.

3. Replacing the Solenoid

Replacing the solenoid is a relatively simple task. The following steps will show you how to replace the solenoid on a golf cart:

1. Turn off the power to the golf cart. This can be done by disconnecting the negative battery cable.
2. Locate the solenoid. The solenoid is usually located near the starter motor.
3. Remove the solenoid mounting bolts. There are usually two or three bolts that hold the solenoid in place.
4. Disconnect the solenoid wires. There are two wires connected to the solenoid. Disconnect the wires by carefully pulling them off of the terminals.
5. Install the new solenoid. Align the new solenoid with the mounting holes and install the mounting bolts.
6. Reconnect the solenoid wires. Carefully reconnect the wires to the terminals.
7. Reconnect the negative battery cable.
8. Test the solenoid. Turn on the power to the golf cart and try to start the engine. If the engine starts, the solenoid has been replaced correctly.

4. Remove the negative battery cable.

To remove the negative battery cable, you will need a wrench.

1. Locate the negative battery cable. The negative battery cable is usually black and is connected to the negative terminal of the battery.
2. Put the wrench on the nut that is holding the negative battery cable to the battery terminal.
3. Turn the wrench counterclockwise to loosen the nut.
4. Remove the negative battery cable from the battery terminal.

Once the negative battery cable has been removed, you can proceed with replacing the solenoid.

How do I check the solenoid on my golf cart?

1. Locate the solenoid. The solenoid is a cylindrical-shaped device that is typically located near the starter motor. It is usually black or brown in color and has two wires connected to it.
2. Turn off the golf cart’s engine and disconnect the battery. This will prevent you from getting shocked.
3. Use a voltmeter to check the voltage at the solenoid’s terminals. With the voltmeter set to DC volts, connect the positive lead to the solenoid’s positive terminal and the negative lead to the solenoid’s ground terminal. The voltage should be between 12 and 14 volts.
4. Turn on the golf cart’s ignition switch. This should cause the solenoid to click and the starter motor to engage. If the solenoid does not click or the starter motor does not engage, the solenoid is bad and needs to be replaced.

What are the symptoms of a bad solenoid?

• The golf cart will not start.
• The starter motor will not engage.
• The solenoid will click when the ignition switch is turned on.
• The solenoid will be hot to the touch.

How can I prevent a solenoid from going bad?

• Keep the battery terminals clean and corrosion-free.
• Avoid shorting out the solenoid.
• Do not overload the solenoid.
• Replace the solenoid if it is damaged or worn out.

Where can I buy a replacement solenoid?

You can purchase a replacement solenoid from a golf cart dealer or online retailer. When choosing a solenoid, make sure it is the correct size and voltage for your golf cart.

How much does a solenoid replacement cost?

The cost of a solenoid replacement will vary depending on the make and model of your golf cart. The average cost is between $50 and $100.

In this blog post, we have discussed how to check the solenoid on a golf cart. We have covered the following topics:

• The function of the solenoid in a golf cart
• The different types of solenoids used in golf carts
• The symptoms of a faulty solenoid
• How to test a solenoid using a multimeter
• How to replace a solenoid

We hope that this blog post has been helpful in understanding the role of the solenoid in a golf cart and how to check and replace it if necessary.