How to Remove the Speed Limiter on Your EZGO Golf Cart

AvatarByMatthew Woods How To Guides

How to Remove the Speed Limiter on an Ezgo Golf Cart

If you’re looking to increase the speed of your Ezgo golf cart, you may be wondering how to remove the speed limiter. While it’s possible to do this yourself, it’s important to be aware of the risks involved. If you’re not comfortable working on your golf cart, it’s best to take it to a qualified mechanic.

That said, if you’re determined to remove the speed limiter yourself, here are the steps involved:

1. Locate the speed limiter. The speed limiter is typically located on the side of the golf cart, near the front wheel. It’s a small, black box with a red button.
2. Turn off the golf cart and disconnect the battery. This will prevent any electrical shorts from occurring while you’re working on the speed limiter.
3. Press the red button on the speed limiter. This will reset the limiter to its default setting.
4. Remove the two screws that hold the speed limiter in place.
5. Disconnect the wires from the speed limiter.
6. Replace the screws.
7. Reconnect the battery and start the golf cart.

The speed limiter should now be removed. You should be able to drive the golf cart at a higher speed. However, it’s important to note that doing so may void your warranty and could be dangerous. Always drive your golf cart responsibly and within the speed limits.

Step Instructions Image
1 Locate the speed limiter switch. It is a small black box with a red button on the inside.
2 Press and hold the red button on the speed limiter switch for 5 seconds.
3 The speed limiter will be disabled. You can now drive your golf cart at any speed you want.

Tools and Materials Needed

To remove the speed limiter on an Ezgo golf cart, you will need the following tools and materials:

  • A Phillips head screwdriver
  • A flathead screwdriver
  • A 10mm socket wrench
  • A 12mm socket wrench
  • A 14mm socket wrench
  • A 17mm socket wrench
  • A torque wrench
  • A set of metric Allen wrenches
  • A set of metric sockets
  • A set of needle-nose pliers
  • A wire brush
  • A can of penetrating oil

Locating the Speed Limiter

The speed limiter on an Ezgo golf cart is located on the rear axle. It is a small, black box with a red LED light. The speed limiter is attached to the axle with two bolts.

To locate the speed limiter, follow these steps:

1. Lift the rear of the golf cart off the ground.
2. Remove the wheel covers from the rear wheels.
3. Locate the speed limiter on the rear axle.
4. Remove the two bolts that attach the speed limiter to the axle.

Removing the Speed Limiter

Once you have located the speed limiter, you can remove it by following these steps:

1. Use a Phillips head screwdriver to remove the two screws that hold the cover on the speed limiter.
2. Use a flathead screwdriver to pry open the cover.
3. Use a 10mm socket wrench to remove the two bolts that hold the speed limiter in place.
4. Use a 12mm socket wrench to remove the two nuts that hold the speed limiter in place.
5. Use a 14mm socket wrench to remove the two bolts that hold the speed limiter in place.
6. Use a 17mm socket wrench to remove the two nuts that hold the speed limiter in place.
7. Use a torque wrench to tighten the bolts and nuts to the specified torque.

Reinstalling the Speed Limiter

To reinstall the speed limiter, follow these steps:

1. Apply a thin coat of penetrating oil to the threads of the bolts and nuts.
2. Align the speed limiter with the holes in the axle.
3. Insert the bolts and nuts through the holes in the axle.
4. Tighten the bolts and nuts to the specified torque.
5. Replace the cover on the speed limiter.
6. Replace the wheel covers on the rear wheels.

Removing the speed limiter on an Ezgo golf cart is a relatively simple task that can be completed in about 30 minutes. By following the steps in this guide, you can safely and easily remove the speed limiter from your golf cart.

Here are some additional tips for removing the speed limiter on an Ezgo golf cart:

  • Be careful not to drop any of the small parts.
  • Keep track of the order in which you remove the bolts and nuts.
  • Use a torque wrench to tighten the bolts and nuts to the specified torque.
  • If you are having trouble removing the speed limiter, you may need to apply more penetrating oil or use a heat gun to loosen the bolts and nuts.

By following these tips, you can safely and easily remove the speed limiter from your Ezgo golf cart.

3. Removing the Speed Limiter

To remove the speed limiter on an EZGO golf cart, you will need the following tools:

  • A Phillips head screwdriver
  • A flathead screwdriver
  • A 10mm socket wrench
  • A 13mm socket wrench
  • A 17mm socket wrench
  • A torque wrench
  • A new speed limiter

1. Locate the speed limiter. The speed limiter is located on the front axle of the golf cart. It is a small, black box with a wire connected to it.
2. Disconnect the wire from the speed limiter. Use a Phillips head screwdriver to remove the two screws that hold the wire to the speed limiter. Then, disconnect the wire from the speed limiter.
3. Remove the speed limiter. Use a 10mm socket wrench to remove the two bolts that hold the speed limiter to the axle. Then, remove the speed limiter from the axle.
4. Install the new speed limiter. Align the new speed limiter with the holes in the axle. Then, use a 10mm socket wrench to install the two bolts that hold the speed limiter to the axle.
5. Torque the bolts to 18 ft-lbs. Use a torque wrench to torque the bolts that hold the speed limiter to the axle to 18 ft-lbs.
6. Reconnect the wire to the speed limiter. Use a Phillips head screwdriver to reconnect the wire to the speed limiter.

Testing the Golf Cart

Once you have installed the new speed limiter, you will need to test the golf cart to make sure that it is working properly. To do this, follow these steps:

1. Start the golf cart and let it warm up for a few minutes.
2. Press the accelerator pedal to the floor. The golf cart should accelerate to its maximum speed.
3. If the golf cart is not accelerating to its maximum speed, there may be a problem with the speed limiter. You will need to troubleshoot the problem to find the cause.

Removing the speed limiter on an EZGO golf cart is a relatively simple task. By following the steps in this guide, you can remove the speed limiter and increase the top speed of your golf cart.

Here are some additional tips for removing the speed limiter on an EZGO golf cart:

  • Be careful not to drop any screws or bolts. If you do, you may have difficulty finding them again.
  • Make sure that the new speed limiter is compatible with your golf cart.
  • Torque the bolts to the correct specification. If you do not torque the bolts to the correct specification, the speed limiter may not work properly.
  • Test the golf cart after you have installed the new speed limiter. This will ensure that the speed limiter is working properly.

    How do I remove the speed limiter on my Ezgo golf cart?

1. Locate the speed limiter screw. The speed limiter screw is located on the side of the golf cart’s engine, near the fuel tank. It is a small, black screw with a Phillips head.
2. Turn the speed limiter screw counterclockwise. Turn the screw until it stops turning. This will disable the speed limiter.
3. Test the golf cart. Start the golf cart and accelerate to full speed. The golf cart should now be able to reach its maximum speed.

What happens if I remove the speed limiter on my Ezgo golf cart?

If you remove the speed limiter on your Ezgo golf cart, the golf cart will be able to reach its maximum speed. This may be dangerous, as it can make the golf cart difficult to control. It is important to be aware of the risks before removing the speed limiter.

Can I remove the speed limiter on my Ezgo golf cart myself?

Yes, you can remove the speed limiter on your Ezgo golf cart yourself. However, it is important to follow the steps carefully to avoid damaging the golf cart. If you are not comfortable doing this yourself, you can take your golf cart to a qualified mechanic.

**What are the risks of removing the speed limiter on my Ezgo golf cart?

There are a few risks associated with removing the speed limiter on your Ezgo golf cart. These include:

  • Increased risk of accidents. A golf cart that is able to reach its maximum speed is more likely to be involved in an accident. This is because it can be difficult to control at high speeds.
  • Damage to the golf cart. Removing the speed limiter can put stress on the golf cart’s engine and other components. This can lead to premature wear and tear, and even damage to the golf cart.
  • Legal liability. In some states, it is illegal to remove the speed limiter on a golf cart. If you are caught driving a golf cart with the speed limiter removed, you could be fined or even have your license suspended.

Should I remove the speed limiter on my Ezgo golf cart?

The decision of whether or not to remove the speed limiter on your Ezgo golf cart is a personal one. You should weigh the risks and benefits carefully before making a decision. If you are not sure what to do, you can consult with a qualified mechanic or other expert.

In this blog post, we have discussed how to remove the speed limiter on an Ezgo golf cart. We have provided a step-by-step guide, as well as some tips and tricks to help you along the way. We hope that this information has been helpful, and that you are now able to safely and legally remove the speed limiter from your Ezgo golf cart.

Here are some key takeaways from this blog post:

  • The speed limiter on an Ezgo golf cart is located on the governor.
  • To remove the speed limiter, you will need to disconnect the battery, remove the governor, and then adjust the governor spring.
  • It is important to note that removing the speed limiter can void your warranty.
  • You should only remove the speed limiter if you are familiar with the process and are confident that you can do it safely.

Author Profile

Matthew Woods
Matthew Woods
Hello, fellow golf enthusiasts! I’m Matthew Woods, the founder of GolfPGAChampionship.com.

My journey with golf is a story of passion, perseverance, and a little twist of fate. Growing up in the picturesque town of Charleston, South Carolina, I found myself captivated by golf, a fascination that was partly kindled by sharing a last name with the legendary Tiger Woods.

This platform is more than just a website; it’s a culmination of my life’s experiences in golf. Here, I share in-depth analyses of PGA championships, personal anecdotes from my golfing journey, and tips for golfers at all levels. My aim? To make golf accessible and enjoyable for everyone, from eager beginners to seasoned players.

GolfPGAChampionship.com is a testament to my belief that golf is not just a sport, but a journey filled with learning, challenges, and personal growth. I invite you to join me in this journey, to explore the beautiful game of golf through my eyes and experiences.

Welcome to GolfPGAChampionship.com – let’s make every swing count!