How to Remove a Golf Cart Governor: A Step-by-Step Guide

AvatarByMatthew Woods How To Guides

How to Remove a Golf Cart Governor

If you’re looking to increase the speed of your golf cart, one of the easiest ways to do so is to remove the governor. The governor is a device that limits the speed of the cart by restricting the flow of fuel to the engine. By removing the governor, you can free up the engine and allow it to reach its full potential.

Removing a golf cart governor is a relatively simple task, but it does require some basic mechanical skills. In this article, we’ll walk you through the process step-by-step. We’ll also provide some tips on how to safely and effectively remove the governor without damaging your golf cart.

So if you’re ready to take your golf cart to the next level, read on!

What is a Golf Cart Governor?

A golf cart governor is a device that limits the speed of the cart by restricting the flow of fuel to the engine. The governor is typically located on the engine or fuel line. It works by using a spring-loaded valve to regulate the amount of fuel that can flow to the engine. When the engine reaches a certain speed, the valve closes and restricts the flow of fuel. This limits the amount of power that the engine can produce and, as a result, limits the speed of the cart.

Why Would You Want to Remove a Golf Cart Governor?

There are a few reasons why you might want to remove the governor from your golf cart.

  • To increase speed. The most obvious reason to remove the governor is to increase the speed of your golf cart. By removing the governor, you can free up the engine and allow it to reach its full potential. This can give you a significant increase in speed, making it easier to get around the course quickly.
  • To improve performance. In addition to increasing speed, removing the governor can also improve the performance of your golf cart. By removing the governor, you can allow the engine to breathe more freely and produce more power. This can make your cart feel more responsive and make it easier to accelerate.
  • To save money. Removing the governor can also save you money on gas. By allowing the engine to run at its full potential, you can reduce the amount of gas that you use. This can add up to significant savings over time.

How to Remove a Golf Cart Governor

Removing a golf cart governor is a relatively simple task, but it does require some basic mechanical skills. In this section, we’ll walk you through the process step-by-step.

1. Gather your tools. Before you begin, you’ll need to gather the following tools:

  • A wrench
  • A screwdriver
  • A pair of pliers
  • A socket set
  • A wire brush
  • A can of penetrating oil

2. Locate the governor. The governor is typically located on the engine or fuel line. It’s a small, cylindrical device with a spring-loaded valve.

3. Remove the governor. To remove the governor, you’ll need to first disconnect the fuel line. Then, you’ll need to loosen the bolts that hold the governor in place. Once the bolts are loose, you can carefully remove the governor.

4. Clean the governor. Once the governor is removed, you’ll need to clean it with a wire brush. This will remove any dirt or debris that may be stuck on the valve.

5. Reinstall the governor. Once the governor is clean, you can reinstall it. Be sure to tighten the bolts securely.

6. Test the cart. Once the governor is reinstalled, you can test the cart to make sure that it’s working properly.

Tips for Removing a Golf Cart Governor

Here are a few tips for safely and effectively removing a golf cart governor:

  • Be careful not to damage the governor. The governor is a delicate device, so be careful not to damage it when you’re removing it.
  • Use penetrating oil. If the bolts are stuck, you can use penetrating oil to help loosen them.
  • Work slowly and carefully. Don’t rush the process. Take your time and work slowly and carefully to avoid damaging the governor.
  • Test the cart. Once the governor is reinstalled, be sure to test the cart to make sure that it’s working properly.

    Step Instructions Image
    1 Locate the governor on your golf cart. It is usually a small black box located near the engine.
    2 Disconnect the battery cables from the golf cart. This will prevent the engine from starting while you are working on it.
    3 Remove the screws that hold the governor in place. Once the screws are removed, you should be able to lift the governor out of the golf cart.
    4 Install the new governor. Make sure that the governor is installed in the same orientation as the old one.
    5 Reconnect the battery cables to the golf cart.

    A golf cart governor is a device that limits the speed of a golf cart. It is typically located on the engine of the golf cart and is a small, cylindrical device with a metal rod attached to it. The governor works by limiting the amount of fuel that is allowed to enter the engine, which in turn limits the speed of the golf cart.

    There are a few reasons why you might want to remove the governor from your golf cart. First, if you want to increase the speed of your golf cart, removing the governor will allow you to do so. Second, if the governor is malfunctioning, removing it will allow you to troubleshoot the problem. Finally, if you are planning to modify your golf cart, removing the governor may be necessary.

    Tools and Materials

    The following tools and materials are required to remove a golf cart governor:

    • Golf cart governor
    • Wrench
    • Pliers
    • Safety glasses

    Locating the Governor

    The governor is located on the engine of the golf cart. It is a small, cylindrical device with a metal rod attached to it. The governor is typically located near the carburetor.

    Removing the Governor

    To remove the governor, follow these steps:

    1. Locate the governor. The governor is located on the engine of the golf cart. It is a small, cylindrical device with a metal rod attached to it. The governor is typically located near the carburetor.
    2. Disconnect the fuel line. The fuel line is connected to the governor. Disconnect the fuel line by unscrewing the fitting at the end of the fuel line.
    3. Remove the governor bolts. There are two bolts that hold the governor in place. Use a wrench to loosen and remove the bolts.
    4. Remove the governor. Once the bolts are removed, the governor can be removed from the engine.

    Troubleshooting

    If you are having trouble removing the governor, there are a few things you can check. First, make sure that you have the correct tools and materials. Second, make sure that you are following the instructions correctly. Finally, if you are still having trouble, you can contact a qualified mechanic for help.

    Removing the governor from a golf cart is a relatively simple process. However, it is important to follow the instructions carefully to avoid damaging the golf cart. If you are not comfortable performing this procedure, you can contact a qualified mechanic for help.

    Removing the Governor

    To remove the governor from a golf cart, you will need the following tools:

    • Wrench
    • Pliers

    1. Locate the governor. The governor is a small, cylindrical device that is located on the engine. It is usually located near the carburetor.
    2. Disconnect the wires. There will be two wires connected to the governor. Disconnect these wires by carefully pulling them off of the terminals.
    3. Loosen the bolts. There will be two bolts that hold the governor in place. Use the wrench to loosen these bolts.
    4. Remove the governor. Once the bolts are loose, use the pliers to remove the governor from the engine.

    Be careful not to damage the governor or the engine when removing it.

    Installing the New Governor

    To install the new governor, you will need the following tools:

    • Wrench
    • Pliers

    1. Locate the mounting holes. The governor will have two mounting holes. These holes will be located on the engine.
    2. Align the governor. Align the governor with the mounting holes on the engine.
    3. Insert the bolts. Insert the bolts through the governor and into the mounting holes on the engine.
    4. Tighten the bolts. Use the wrench to tighten the bolts until they are snug.

    Make sure the governor is properly installed and that it is not loose.

    Removing and installing a golf cart governor is a relatively simple task. However, it is important to follow the steps carefully in order to avoid damaging the governor or the engine. If you are not comfortable performing this task, it is best to have a qualified technician do it for you.

    How do I remove a golf cart governor?

    1. Locate the governor. The governor is a small, cylindrical device that is typically located on the engine. It is usually made of metal and has a number of small holes in it.
    2. Turn off the engine and disconnect the battery. This will prevent the engine from starting while you are working on it.
    3. Remove the governor mounting bolts. The governor is usually held in place by two or three bolts. Use a wrench to loosen and remove these bolts.
    4. Remove the governor. Once the bolts are removed, you can carefully lift the governor off of the engine. Be careful not to damage the governor or the engine.
    5. Install the new governor. If you are replacing the governor, make sure that you install the new one in the same orientation as the old one.
    6. Reattach the battery and start the engine. Once the governor is installed, you can reconnect the battery and start the engine. The engine should now be running without the governor.

    What are the symptoms of a bad golf cart governor?

    There are a few symptoms that can indicate that a golf cart governor is bad. These include:

    • The engine is running too fast.
    • The engine is hard to start.
    • The engine is making strange noises.
    • The engine is losing power.

    If you notice any of these symptoms, it is important to have the governor checked by a qualified technician.

    How can I prevent a golf cart governor from failing?

    There are a few things you can do to help prevent a golf cart governor from failing. These include:

    • Keeping the engine well-maintained.
    • Changing the oil and filter regularly.
    • Inspecting the governor for damage regularly.
    • Replacing the governor if it is damaged or worn out.

    By following these tips, you can help keep your golf cart governor running smoothly and efficiently.

    Where can I buy a golf cart governor?

    Golf cart governors are available for purchase at most golf cart dealerships and online retailers. When choosing a governor, it is important to make sure that it is compatible with your golf cart’s engine.

    How much does a golf cart governor cost?

    The cost of a golf cart governor varies depending on the brand and model. Generally, governors cost between $50 and $100.

    Can I remove a golf cart governor myself?

    Yes, you can remove a golf cart governor yourself. However, it is important to note that this is a relatively complex procedure and should only be attempted by someone who is familiar with working on golf carts. If you are not comfortable working on your own golf cart, it is best to have the governor removed by a qualified technician.

    In this blog post, we have discussed how to remove a golf cart governor. We have provided step-by-step instructions on how to do this safely and effectively. We have also discussed the different types of governors and the reasons why you might want to remove one. We hope that this information has been helpful and that you are now able to remove your golf cart governor safely and easily.

    Here are some key takeaways from this blog post:

    • Golf cart governors are devices that limit the speed of a golf cart.
    • There are two main types of governors: mechanical and electronic.
    • Mechanical governors are typically located on the engine, while electronic governors are located on the accelerator pedal.
    • Removing a golf cart governor can increase the speed of the cart, but it can also be dangerous.
    • If you decide to remove a golf cart governor, be sure to do so carefully and follow the instructions in this blog post.

    Author Profile

    Matthew Woods
    Matthew Woods
    Hello, fellow golf enthusiasts! I’m Matthew Woods, the founder of GolfPGAChampionship.com.

    My journey with golf is a story of passion, perseverance, and a little twist of fate. Growing up in the picturesque town of Charleston, South Carolina, I found myself captivated by golf, a fascination that was partly kindled by sharing a last name with the legendary Tiger Woods.

    This platform is more than just a website; it’s a culmination of my life’s experiences in golf. Here, I share in-depth analyses of PGA championships, personal anecdotes from my golfing journey, and tips for golfers at all levels. My aim? To make golf accessible and enjoyable for everyone, from eager beginners to seasoned players.

    GolfPGAChampionship.com is a testament to my belief that golf is not just a sport, but a journey filled with learning, challenges, and personal growth. I invite you to join me in this journey, to explore the beautiful game of golf through my eyes and experiences.

    Welcome to GolfPGAChampionship.com – let’s make every swing count!