How to Remove the Speed Limiter on Your Electric Golf Cart

AvatarByMatthew Woods How To Guides

How to Remove the Speed Limiter on an Electric Golf Cart

Electric golf carts are a convenient way to get around the course, but they can be a bit limiting when it comes to speed. If you’re looking to increase the top speed of your golf cart, you may be able to do so by removing the speed limiter.

This article will provide you with a step-by-step guide on how to remove the speed limiter on an electric golf cart. However, it is important to note that this process may vary depending on the make and model of your golf cart. Be sure to consult your owner’s manual before proceeding.

With that said, let’s get started!

Step Action Explanation
1 Locate the speed limiter The speed limiter is usually a small black box located near the battery.
2 Remove the speed limiter Unscrew the screws that hold the speed limiter in place and remove it.
3 Test the golf cart Turn on the golf cart and accelerate to see if the speed limiter has been removed.

How To Remove Speed Limiter On Electric Golf Cart?

Electric golf carts are a great way to get around the course, but they can be a bit slow. If you’re looking to increase the speed of your golf cart, you may need to remove the speed limiter. This can be a relatively simple process, but it’s important to follow the steps carefully to avoid damaging your cart.

Identify the speed limiter

The speed limiter is usually a small electronic device located on the controller board. It may be a black box with a few wires attached, or it may be integrated into the controller board.

To find the speed limiter, you’ll need to locate the controller board. This is usually located under the seat or in the trunk of the golf cart. Once you’ve found the controller board, look for a small black box with a few wires attached. This is the speed limiter.

Locate the speed limiter’s wiring

The speed limiter is connected to the controller board by two wires. One wire is the power wire, and the other wire is the signal wire.

The power wire is usually a red wire, and it’s connected to the positive terminal of the battery. The signal wire is usually a black wire, and it’s connected to the controller board.

To remove the speed limiter, you’ll need to disconnect the two wires. To do this, you’ll need to use a wire stripper to remove the insulation from the ends of the wires. Once the insulation is removed, you can disconnect the wires by twisting them together and then pulling them apart.

Remove the speed limiter

Once you’ve disconnected the speed limiter’s wires, you can remove the speed limiter from the controller board. To do this, you’ll need to use a small screwdriver to pry the speed limiter off of the controller board.

Be careful not to damage the controller board when you’re removing the speed limiter. Once the speed limiter is removed, you can reinstall the controller board in the golf cart.

Test the golf cart

Now that you’ve removed the speed limiter, it’s time to test the golf cart. Start the golf cart and drive it around the course. Make sure that the golf cart is now able to reach the desired speed.

If the golf cart is not able to reach the desired speed, you may need to adjust the governor. The governor is a device that controls the maximum speed of the golf cart. To adjust the governor, you’ll need to consult the owner’s manual for your golf cart.

Removing the speed limiter on an electric golf cart is a relatively simple process, but it’s important to follow the steps carefully to avoid damaging your cart. By following the steps in this guide, you can safely remove the speed limiter and increase the speed of your golf cart.

How To Remove Speed Limiter On Electric Golf Cart?

Electric golf carts are a great way to get around the course, but they can be a bit slow. If you’re looking to increase the speed of your golf cart, you may need to remove the speed limiter. This can be a relatively simple process, but it is important to follow the steps carefully in order to avoid damaging your golf cart.

Tools and Materials

To remove the speed limiter on an electric golf cart, you will need the following tools and materials:

  • A voltmeter
  • A wire cutter
  • A soldering iron
  • A piece of heat shrink tubing
  • A programming tool (optional)

Instructions

1. Locate the speed limiter. The speed limiter is usually located on the controller board. It may be a small black box with a potentiometer or a chip.
2. Disconnect the battery. Before you begin working on the golf cart, disconnect the battery to avoid any electrical shocks.
3. Remove the speed limiter’s wiring. To disconnect the speed limiter’s wiring, you will need to cut the power wire and the signal wire. Be sure to label the wires so that you can reconnect them later.
4. Reprogram the controller board. Once the speed limiter’s wiring has been disconnected, you will need to reprogram the controller board. This can be done by using a programming tool or by following the instructions in the controller board’s manual.
5. Reconnect the battery. Once the controller board has been reprogrammed, you can reconnect the battery.
6. Test the golf cart. Take the golf cart for a test drive to make sure that the speed limiter has been removed.

Removing the speed limiter on an electric golf cart is a relatively simple process, but it is important to follow the steps carefully in order to avoid damaging your golf cart. If you are not comfortable working on electrical components, it is best to have a professional do the work for you.

How do I remove the speed limiter on my electric golf cart?

1. Locate the speed limiter. The speed limiter is typically a small, black box located on the controller board. It may be labeled “Speed Limiter” or “Governor”.
2. Disconnect the battery. Before you can remove the speed limiter, you need to disconnect the battery. This will prevent any damage to the controller board.
3. Remove the speed limiter. Once the battery is disconnected, you can remove the speed limiter. Use a small screwdriver to pry off the cover. Inside, you will find a small circuit board. Remove the circuit board by disconnecting the wires.
4. Reinstall the battery. Once the speed limiter is removed, you can reinstall the battery. Make sure to connect the battery terminals in the correct order.
5. Test the golf cart. Once the battery is reconnected, test the golf cart to make sure the speed limiter has been removed. You should now be able to drive the golf cart at the desired speed.

What are the risks of removing the speed limiter on an electric golf cart?

There are a few risks associated with removing the speed limiter on an electric golf cart. These include:

  • Increased risk of accidents. Removing the speed limiter can allow the golf cart to reach speeds that are unsafe for the driver and passengers. This can increase the risk of accidents.
  • Damage to the golf cart. Driving the golf cart at high speeds can damage the engine, transmission, and other components. This can lead to costly repairs.
  • Legal liability. In some states, it is illegal to remove the speed limiter on an electric golf cart. If you are caught driving a golf cart with the speed limiter removed, you could be fined or even arrested.

Is it legal to remove the speed limiter on an electric golf cart?

The legality of removing the speed limiter on an electric golf cart varies from state to state. In some states, it is illegal to remove the speed limiter. In other states, it is legal to remove the speed limiter, but only if the golf cart is being used on private property. It is important to check the laws in your state before removing the speed limiter on your electric golf cart.

How do I know if my golf cart has a speed limiter?

There are a few ways to tell if your golf cart has a speed limiter. These include:

  • Checking the owner’s manual. The owner’s manual will typically include information about the golf cart’s speed limiter.
  • Looking for a speed limiter sticker. Some golf carts have a speed limiter sticker located on the dashboard or near the speed control.
  • Testing the golf cart’s speed. If you can’t find a speed limiter sticker or the owner’s manual doesn’t mention a speed limiter, you can test the golf cart’s speed to see if it is limited. Drive the golf cart at full throttle and see how fast it goes. If the golf cart reaches a maximum speed of 20 mph or less, it is likely that it has a speed limiter.

Can I install a speed limiter on my electric golf cart?

Yes, you can install a speed limiter on your electric golf cart. There are a number of different speed limiters available on the market. You can find speed limiters that are designed for specific golf cart models, as well as universal speed limiters that can be installed on any golf cart.

How do I install a speed limiter on my electric golf cart?

Installing a speed limiter on your electric golf cart is a relatively simple process. The following steps will provide you with a general overview of how to install a speed limiter:

1. Locate the speed limiter. The speed limiter is typically a small, black box located on the controller board. It may be labeled “Speed Limiter” or “Governor”.
2. Disconnect the battery. Before you can install the speed limiter, you need to disconnect the battery. This will prevent any damage to the controller board.
3. Install the speed limiter. Once the battery is disconnected, you can install the speed limiter. Use a small screwdriver to pry off the cover. Inside, you will find a small circuit board. Connect the speed limiter to the controller board according to the manufacturer’s instructions.
4. Reinstall the battery. Once the speed limiter is installed, you can reinstall the battery. Make sure to connect the battery terminals in the correct order.
5. Test the golf cart. Once the battery is reconnected, test the golf cart to make sure the speed limiter is

there are a few different ways to remove the speed limiter on an electric golf cart. The most common method is to use a voltmeter to locate the limiter, then disconnect the wires leading to it. Another option is to use a chip programmer to change the speed limit setting. Finally, it is also possible to remove the limiter by physically modifying the cart’s controller. Each of these methods has its own advantages and disadvantages, so it is important to choose the one that is best suited for your individual needs.

No matter which method you choose, it is important to be aware of the risks involved. Modifying your golf cart’s speed limiter can void your warranty and make it unsafe to operate. It is also important to follow all of the necessary safety precautions when working on your golf cart.

By following these steps, you can safely remove the speed limiter on your electric golf cart and enjoy the freedom of driving at your own desired speed.

Author Profile

Matthew Woods
Matthew Woods
Hello, fellow golf enthusiasts! I’m Matthew Woods, the founder of GolfPGAChampionship.com.

My journey with golf is a story of passion, perseverance, and a little twist of fate. Growing up in the picturesque town of Charleston, South Carolina, I found myself captivated by golf, a fascination that was partly kindled by sharing a last name with the legendary Tiger Woods.

This platform is more than just a website; it’s a culmination of my life’s experiences in golf. Here, I share in-depth analyses of PGA championships, personal anecdotes from my golfing journey, and tips for golfers at all levels. My aim? To make golf accessible and enjoyable for everyone, from eager beginners to seasoned players.

GolfPGAChampionship.com is a testament to my belief that golf is not just a sport, but a journey filled with learning, challenges, and personal growth. I invite you to join me in this journey, to explore the beautiful game of golf through my eyes and experiences.

Welcome to GolfPGAChampionship.com – let’s make every swing count!