How Do You Take The Governor Off A Golf Cart?

AvatarByMatthew Woods Golf Blog

How to Take the Governor Off a Golf Cart

Golf carts are a convenient way to get around a golf course, but they can be a bit slow. If you’re looking for a way to increase your speed, you may be wondering how to take the governor off a golf cart.

The governor is a device that limits the speed of a golf cart. It’s usually located on the engine, and it can be removed by disconnecting a few wires. However, before you do this, it’s important to understand the risks involved.

Removing the governor can void your warranty and make your golf cart unsafe. It can also increase the risk of engine damage. If you decide to proceed, you should do so at your own risk.

With that said, here are the steps on how to take the governor off a golf cart:

1. Locate the governor. The governor is usually located on the engine, near the carburetor. It’s a small, black box with a few wires attached to it.
2. Disconnect the wires. There are usually two wires connected to the governor. Disconnect these wires by carefully pulling them off the terminals.
3. Test the golf cart. Once you’ve disconnected the wires, start the golf cart and let it run for a few minutes. The golf cart should now be running faster than it was before.

Note: If you’re not comfortable working on your golf cart, you should take it to a qualified mechanic. They will be able to remove the governor safely and without damaging your golf cart.

| Step | Action | Result |
|—|—|—|
| 1 | Locate the governor on your golf cart. | The governor is a small, black box located on the side of the golf cart’s engine. |
| 2 | Remove the governor’s cover. | The cover is held in place by two screws. Remove the screws and set the cover aside. |
| 3 | Locate the governor’s adjustment screw. | The adjustment screw is located inside the governor. It is a small, silver screw. |
| 4 | Turn the adjustment screw clockwise. | Turning the adjustment screw clockwise will increase the speed of the golf cart. |
| 5 | Test the golf cart. | Once you have adjusted the governor, test the golf cart to make sure that it is running at the desired speed. |

How Do You Take The Governor Off A Golf Cart?

Tools and Materials Needed

  • Golf cart
  • Wrench
  • Socket
  • Extension
  • Screwdriver
  • Penetrating oil

Step-by-Step Instructions

1. Locate the governor. The governor is a small device located on the engine of the golf cart. It is usually a black box with a wire connected to it.
2. Disconnect the battery. This will prevent the engine from starting while you are working on it.
3. Remove the access panel. The access panel is usually located on the bottom of the golf cart. It is held in place by a few screws. Remove the screws and set the panel aside.
4. Locate the governor. The governor is a small device located on the engine of the golf cart. It is usually a black box with a wire connected to it.
5. Disconnect the governor. The governor is connected to the engine by a wire. Disconnect the wire by unscrewing the connector.
6. Replace the access panel. Replace the access panel and secure it with the screws.
7. Reconnect the battery. Reconnect the battery and start the golf cart.

Troubleshooting

If you are having trouble removing the governor, you may need to use a penetrating oil to loosen the screws. Apply the oil to the screws and let it sit for a few minutes before trying to remove them again.

If you are still having trouble, you may need to take the golf cart to a qualified mechanic.

Removing the governor from a golf cart is a relatively simple task. By following these steps, you can safely and easily remove the governor from your golf cart.

How Do You Take The Governor Off A Golf Cart?

A golf cart governor is a device that limits the speed of a golf cart. It is typically located on the engine and is either a mechanical or electronic device. Mechanical governors use a spring-loaded arm to restrict the throttle, while electronic governors use a sensor to monitor the engine speed and cut off fuel if the speed exceeds a predetermined limit.

There are a few reasons why you might want to remove the governor from your golf cart. One reason is to increase the speed of the cart. Another reason is to improve fuel economy. Finally, some people remove the governor simply because they want to be able to drive their golf cart faster.

If you decide to remove the governor from your golf cart, it is important to do so carefully and to follow the instructions provided by the manufacturer. Removing the governor can void your warranty, and it can also make your golf cart unsafe to operate.

To remove the governor from a golf cart, you will need the following tools:

  • A socket wrench
  • A screwdriver
  • A pair of pliers

1. Locate the governor. The governor is typically located on the engine. It is a small, black box with a wire connected to it.
2. Disconnect the wire from the governor. The wire from the governor is typically connected to the throttle. Use a screwdriver to disconnect the wire.
3. Remove the screws that hold the governor in place. There are usually two or three screws that hold the governor in place. Use a socket wrench to remove the screws.
4. Remove the governor. Once the screws are removed, you can lift the governor off of the engine.

That’s it! You have now successfully removed the governor from your golf cart.

Note: If you are not comfortable working on your golf cart, you should have a qualified technician remove the governor for you.

Troubleshooting

If you have problems after removing the governor from your golf cart, there are a few things you can check.

  • Make sure that the wire from the governor is disconnected. If the wire is still connected, the governor will still be limiting the speed of the cart.
  • Check the throttle. The throttle may be stuck open, which could cause the cart to accelerate too quickly.
  • Check the engine. The engine may not be able to handle the increased speed. If the engine is struggling, you may need to upgrade the engine or install a higher-capacity fuel pump.

If you are still having problems after checking these things, you should have a qualified technician look at your golf cart.

Safety Tips

Removing the governor from your golf cart can increase the speed of the cart. This can make the cart more dangerous to operate. Here are a few safety tips to keep in mind if you decide to remove the governor from your golf cart:

  • Wear a helmet and other safety gear. A helmet can protect your head in the event of an accident. Other safety gear, such as gloves and eye protection, can also help to protect you from injury.
  • Be aware of your surroundings. When you are driving a golf cart, it is important to be aware of other people and vehicles in your area. Be especially careful when driving near children and pets.
  • Slow down and use caution when driving on wet or slippery surfaces. Wet or slippery surfaces can make it difficult to control the cart. Slow down and use caution when driving on these surfaces.
  • Don’t drink and drive. Drinking and driving is dangerous, and it is illegal in most states. If you have been drinking, don’t get behind the wheel of a golf cart.

By following these safety tips, you can help to reduce the risk of accidents when driving a golf cart with the governor removed.

Removing the governor from a golf cart can increase the speed of the cart, but it also makes the cart more dangerous to operate. If you decide to remove the governor from your golf cart, be sure to do so carefully and to follow the instructions provided by the manufacturer. Also, be sure to take the necessary safety precautions to reduce the risk of accidents.

How do you take the governor off a golf cart?

There are a few different ways to remove the governor from a golf cart. The most common method is to use a screwdriver to pry open the governor housing and remove the governor spring. Another method is to use a drill to drill out the governor rivets. Finally, you can also use a grinder to grind off the governor housing.

What are the risks of removing the governor from a golf cart?

There are a few risks associated with removing the governor from a golf cart. First, it can make the cart go faster than it was designed to, which can increase the risk of accidents. Second, it can make the cart harder to control, which can also increase the risk of accidents. Third, it can void the warranty on the cart.

Is it legal to remove the governor from a golf cart?

The legality of removing the governor from a golf cart varies from state to state. In some states, it is illegal to remove the governor from a golf cart, while in other states it is legal. It is important to check the laws in your state before removing the governor from your golf cart.

How do I put the governor back on a golf cart?

To put the governor back on a golf cart, you will need to reverse the steps you took to remove it. First, you will need to install the governor spring in the governor housing. Then, you will need to close the governor housing and secure it with the screws or rivets.

What are some other ways to increase the speed of a golf cart?

There are a few other ways to increase the speed of a golf cart without removing the governor. One way is to upgrade the engine. Another way is to install a larger fuel tank. Finally, you can also install a performance exhaust system.

I’m not comfortable removing the governor from my golf cart. Can I take it to a mechanic to have it done?

Yes, you can take your golf cart to a mechanic to have the governor removed. The mechanic will be able to remove the governor safely and correctly.

In this blog post, we have discussed how to take the governor off a golf cart. We have provided a step-by-step guide, as well as tips and tricks to help you safely and successfully remove the governor from your golf cart. We hope that this information has been helpful, and that you are now able to enjoy your golf cart without the restriction of the governor.

Here are some key takeaways from this blog post:

  • The governor is a device that limits the speed of a golf cart.
  • It is located on the engine or transmission.
  • To remove the governor, you will need to find the governor and disconnect the wires.
  • You may also need to remove some bolts or screws.
  • Be sure to reconnect the wires and bolts or screws once you have removed the governor.
  • Removing the governor can void your warranty.
  • It is always best to consult with a qualified mechanic before removing the governor from your golf cart.

Author Profile

Matthew Woods
Matthew Woods
Hello, fellow golf enthusiasts! I’m Matthew Woods, the founder of GolfPGAChampionship.com.

My journey with golf is a story of passion, perseverance, and a little twist of fate. Growing up in the picturesque town of Charleston, South Carolina, I found myself captivated by golf, a fascination that was partly kindled by sharing a last name with the legendary Tiger Woods.

This platform is more than just a website; it’s a culmination of my life’s experiences in golf. Here, I share in-depth analyses of PGA championships, personal anecdotes from my golfing journey, and tips for golfers at all levels. My aim? To make golf accessible and enjoyable for everyone, from eager beginners to seasoned players.

GolfPGAChampionship.com is a testament to my belief that golf is not just a sport, but a journey filled with learning, challenges, and personal growth. I invite you to join me in this journey, to explore the beautiful game of golf through my eyes and experiences.

Welcome to GolfPGAChampionship.com – let’s make every swing count!